Dynaflite DYFA3040 Bedienungsanleitung

• BUILDS QUICKLY• REALISTIC FUN SCALE® MODEL• HUGE, 89" WINGSPAN (IMAA Legal)READ THROUGH THIS INSTRUCTION MANUAL FIRST. IT CONTAINSIMPORTANT INS

[.-111. Build both elevators at the same time. Cutthe leading edges from 5/8" x 1/2" x 30" balsaand pin them to the plan.The leftover 5

5. Cut and fit the ribs from the remainder ofthe 3/16" x 3/8" x 24" balsa. Cut the longer ribsfirst. When satisfied with the fit, glue

Q 1.The fuselage plan is in two pieces. Cut theplan as indicated and tape the two partstogether. Cut the fuselage top view from theplan. Cut the drawi

[-] 7. Locate one of the die-cut 1/8" ply forwardfuselage sides. Cut off the front end of this sidealong the embossed line.This will establish tw

Q 12. Glue the die-cut 1/8" ply fuselage top andbottom decks to the right fuselage side. Theparts interlock. Do not glue the bulkheads to thedeck

Q 19. Cut a stringer from 1/8" x 1/4" x 31"basswood to length and glue into place to thebottom of formers AB and BB.The remainder ofthi

you will be using the Great Planes IsolationMount™ you will need to reposition theMounting Grommets as shown on the plan.Note: Depending on the type o

Note: If you will be entering your Chipmunk inIMAA events you need to review theirrequirements for servo and control linkagesizes. They require high-t

1-1 37. Glue two sheets of 1/8" x 3" x 24" balsatogether to form a sheet 6" wide. Sand the outerside of this sheet flat and smooth

Q Q 1. Lay the right wing plan on your buildingboard and cover it with Plan Protector.Note: It will be easier if you prepare all fourleading edge wing

Introduction...2Precautions ...2Preparations ...

plan. There are two doublers for W2. The onewith the long cutout is glued to the side facingthe wing root. This cutout will lock in thelanding gear st

13. Glue the 1/4" x 1/2" x 48" balsa leadingedge stick to the front of the ribs. Align the topof the LE even with the tops of the ribs.

1—1 19. Glue the leading edge skin that youprepared in step 2 to the top spar, ribs and LEusing aliphatic resin. The sheeting extends tothe center of

U U 27. Using a 1/4" bit, drill a hole through thelanding gear rail into the stub block. Radius thetop of the hole to fit the bend in the 1/4&quo

LI 3. After the epoxy has cured, slide the rightpanel back into position. Position the rightpanel flat on your building board and prop theleft tip off

satisfied with the fit, glue the dowels into thewing with 6-minute epoxy. Use caution not toget any epoxy on the fuselage.Q 13. Using the leading edge

plan as a guide to cut the sheeting to the propersize. Glue this piece to the tops of the ribs.1-1 Q 22. GlueW2A into position. Sand theTE ofthe sheet

[-I Q 12. Cut four additional hinge blocks fromthe 1/4" x 1/2" balsa. Glue these into position intheTE of the wing opposite the position of

Q Q 12. Cut four additional hinge blocks fromthe 1/4" x 1/2" balsa. Glue these into position intheTE of the wing opposite the position of th

Q 5. Fit the two die-cut 1/8" ply wing bolt platesfor the wing bolt holes onto the bottom of thewing. Glue these into position over the holes wit

Your Chipmunk is not a toy, but a sophisticatedworking model that functions very much like anactual airplane. Because of its realisticperformance, if

2-1/2"SIDE SHEETING 1.1/4"5"13-1/2"31"36""3"Q 2. Add a stringer to the fuselage from formerDT to HT. Use the s

clevis (GPMQ3814) at the rudder end and a 4-40metal threaded clevis (GPMQ3794) at the servoend with a 4-40 hex nut.CJ 11. Fit the horizontal stab to t

room table for the next steps. Just make sure tocover the table so you don't scratch it or getglue on it, lest - well, you get the idea.Q 18. Whe

Q 1. Finish the cockpits. The cockpit area wasdesigned to be structure free so you can add asmuch detail as desired.The simplest is to glue acouple of

DRILL A 3/32" HOLE1/2" DEEP, IN CENTEROF HINGE SLOTCUT HINGE SLOTWITH HOBBY KNIFEAND #11 BLADED. Use a hobby knife with a #11 blade tomake t

to wipe away excess CA. If you spill a fewdrops of CA on the MonoKote® film youcan use CA Debonder (GPMR6039) to removeit. Or wait until the CA fully

Q 9. Mount the landing gear and 4" wheels(ROBQ1537).Note: Optional landing gear struts are availablefrom Robart that fit this model. These struts

halves next to the fuselage.The balance point isshown on the plan and is 5-1/2" (140mm) aft ofthe leading edge.Q 2. This is the balance point at

arm onto the servos and the servo cords aresecurely connected to the receiver. If you arenot thoroughly familiar with R/C models, ask anexperienced mo

Make all engine adjustments from behind therotating propeller.The engine gets hot! Do not touch the engineduring or immediately after you operate it.M

convenience. GPM is the Great Planes® brand,TOP is the Top Flite® brand and HCA is theHobbico® brand.4-6 Channel Radio with One Standard Servo(Three w

too close to people, power lines and possibleradio interference. If you are a beginner, youare busy enough concentrating on your modelwithout having t

Center Pull

TWO VIEW DRAWINGUse copies of this page to plan your trim scheme-Out Page

A flat, durable, easy-to-handle sanding tool is anecessity for building model airplanes. Great.Planes makes a complete range if Easy-Touch"Bar Sa

the parts to be glued with accelerator, jointhem, then add the CA. This way the CA isguaranteed to cure immediately. Thisprepriming is especially hand

Die-Cut Pattern1 REQ.CHPGIPW061/16" X 3-3/8" X 16" PLYCHPGW05Note: If you will be building functional flaps for yourChipmunk, glue in t

Die-Cut PatternCHPGF05 1 REQ.1/8" X 3" X 36" BALSACHPGF042 REQ.1/8" X 3" X 36" BALSACHPGF03 1 REQ,1/8" X 6-3/8"

1. Cut the stabilizer drawing from the fuselageplan and place it on your building board. Coverthe plan with Great Planes Plan Protector.STAB SHEETING1