Dynaflite DYFA2018 Bedienungsanleitung

• Simple Entry Level Construction• Stable Flight Characteristics• Excellent R/C TrainerREAD THROUGH THIS INSTRUCTION MANUAL FIRST. IT CONTAINSIMPORTAN

CUTTING THE HINGE SLOTSQ 1. Lay the rudder and elevator on the plansheet and mark the hinge locations. Place therudder against the finTE and transfer

trued edge. Apply medium CA to the fuse sidewhere the sheet will contact it. Place the sheetonto the fuse side.FUSE STRUCTUREASSEMBLYQ Q 6. From anoth

I-] 6. Locate the die-cut 1/8" ply forward fusebottom. Place the forward fuse bottom ontothe fuselage. Set the fuselage assembly upright(in its n

Q 13. Use medium CA to glue two pieces of3/16" x 3/16" balsa stick into the cornersbetween the fuse bottom and the fuse sidebetween formers

Note: The Daydream wing, much like thefuselage, is designed with simplicity and easeof building in mind. Always remember to test fitparts before using

touch or be glued to the ribs. They should bethoroughly glued to the spars.Q Q 10. Remove the pins holding the wingpanel to your building surface. Slo

Q Q 19. Remove the die-cut 1/16" balsa wingribs R3 through R10 from the die-cut sheets.Slide the wing ribs into position on thebottom spar Glue t

Q 2. Use a flat blade screwdriver to knock out thecenter of the second R1 ribs between the spars.Q 3. Locate and glue the two die-cut 1/8" plycen

together with the brace installed. Once thebrace fits, use 30-minute epoxy to liberallycover the brace and the two R1 ribs. Also coatthe spars inside

Do not confuse this procedure with "checkingthe C.G."That will be discussed later in the manual.Now that the model is nearly completed, yous

Introduction ...2Precautions ...2Preparation

a tape measure to set the stabilizer tips equaldistance from the nose.Q 3. Use 30-minute epoxy to glue the stabilizerin position on the fuselage, rech

Q 3. Install the servos using the hardware includedwith your radio system. Use the plan as a guideto position the servos laterally in the fuselage.Q4.

arm. Trim the nylon pushrod 1/2" ahead of thethreaded rod.This will allow the threaded rod tobe securely attached. Remove the clevis fromthe serv

The balance point (C.G. - Center of Gravity) islocated under the spar. This is the balance pointat which your model should balance for yourfirst fligh

CHARGE THE BATTERIESThis means with thetransmitter antennacollapsed and the receiver and transmitter on,you should be able to walk at least 100 feetaw

and I will not thereafter perform maneuvers,flights of any sort or landing approaches over apit, spectator or parking area.First of all, if you are fl

your first flights pull the plane back until thereis approximately 8 Ibs. of tension. More tensioncan be used after you get acquainted with thelaunchi

Thermals are a natural phenomenon thathappen outside, by the millions, every singleday of the year. Thermals are responsible formany things including

circle you will be swept along with it. Be carefulwhen thermaling that you don't get so far downwindyou can't make it back to the field to l

bring the sailplane in for a landing higher orfaster than normal to guard against any lastminute sink or gusts and dump the extraaltitude and speed at

flight instructors are available. Contact the AMAat the address or toll-free phone number below:Academy of ModelAeronautics5151 East Memorial DriveMun

top of the slope and "slide" into the top of theslope without encountering any turbulent air.On steeper slopes you may have to be a littlemo

Dynafilte Talon"No matter if the air's light and the airfield's small —you'll be thrilled with the Talon's speed andmaneuvera

6-Minute Pro Epoxy (GPMR6045)30-Minute Pro Epoxy (GPMR6047)4 oz. Pro Wood Glue (GPMR6161)Hand or Electric DrillSealing Iron (TOPR2100)Hobby SawHobby K

•Whenever the instructions tell you to gluepieces together, thin CA should be used.When a specific type of glue is required,the instructions will stat

Gusset: A brace used to reinforce the jointbetween two parts.High-start: A device used to launch a modelglider like a slingshot. This device consists

7Die-Cut Pattern

BUILD THE FORMERSQ 1. Unroll the plan. Re-roll the plan inside outto make it lie flat. Wax paper or Great PlanesPlan Protector" placed over the p

Q 6. Remove the stabilizer from your buildingsurface. Examine and add thick CA glue to anyopen joints, then use your sanding block withmedium (150-gri